Home > Return Code > Vsam Catalog Return Code Is 48 - Reason Code Is Igg0clfo-28

Vsam Catalog Return Code Is 48 - Reason Code Is Igg0clfo-28

Contents

You requested a programmer logical unit that was not system generated (IOTAB xxPRG). Rerun the job. PROGRAMMER ACTION: Rerun the job in a large partition. The ACB for a SHAREOPTIONS(4) KSDS indicates MACRF = ADR or MACRF = CNV but the SHAREOPTIONS(4) file, which you are attempting to open for output, is already open for output have a peek here

Open did not try to verify the file's catalog records. X'74' 116 Return Code=04 Action=OPEN You tried to open a file that was not successfully closed the last time it was opened for output. STEP2 fails with Catalog error. PROGRAMMER ACTION: Use another program to load the file of specify ACB MACRF = NSR (non-shared resources) unit the file is loaded. http://www.ibm.com/support/knowledgecenter/SSLTBW_2.1.0/com.ibm.zos.v2r1.ieam600/bb3009i.htm

Vsam Catalog Return Code Is 48 - Reason Code Is Igg0clfo-28

PROGRAMMER ACTION: Specify SIZE on the EXEC statement to provide adequate GETVIS space. X'DC' 220 Return Code=08 Action=OPEN ACB MACRF = LSR (local shared resources) is specified, but the control interval size of the file being opened is greater than the larger buffer size Company Overview SimoTime Technologies was founded in 1987 and is a privately owned company.

X'D4' 212 Return Code=08 Action=OPEN ACB MACRF = LSR (local shared resources) is specified, but the file being opened is empty (which implies that the file will be loaded). Either the CDLOAD failed, or the service aid encountered I/O errors. The intent is to provide changes as the need arises and in a timeframe that is dependent upon the availability of resources. Iec331i Examples of these incompatibilities are: The DTF BLKSIZE is too large to fit in the maximum RECORDSIZE defined for the file.

Change your program to avoid task contention for the ACB. Igg0cleg-42 X'54' 084 Return Code=08 Action=Request Locate mode was specified for a PUT request of for processing in a user buffer. PROGRAMMER ACTION: Make sure the file-id in your DLBL statement does not specify the name of a default model. http://ibmmainframes.com/about55660.html X'4F' 079 Return Code=08 Action=OPEN A catalog management error was detected during implicit define.

Follow the directions for the error messages that it issues. Idc3007i An error may have occurred during lock Manager processing. X'01' 001 Return Code=04 Action=CBMM GENCB/MODCB/SHOWCB/TESTCB request is invalid.

X'02' 002 Return Code=>0 Action=CLOSE CLOSE or TCLOSE found an invalid control block structure for this ACB. X'38' 056 Return Code=08 Action=Request An error occurred during dynamic assignment of a volume.

Igg0cleg-42

Ask Me Anything about z/OS Security Updated 6:09PM EDT, Fri Apr 1st, 2016 Find out more about z/OS security...ask away for an hour! look at this web-site Save the dump you obtain and the SYSLOG output for later problem determination. Vsam Catalog Return Code Is 48 - Reason Code Is Igg0clfo-28 I gave it a FILE (volume) to use! Idcams Return Codes PROGRAMMER ACTION: Depends on the processing done during the preceding run.

If this does not work, rerun the job in a larger partition. navigate here Therefore, the file status-key-2 may not always be a numeric value that is easy to display. The request cannot be fulfilled by the server File Status Keys Return Codes for Data Files & VSAM Table of Contents v-16.01.01 - vsmfsk01.htm Introduction File Status Key PROGRAMMER ACTION: Because this information was collected during OPEN processing, it cannot be printed. Igd17103i

Here's the defenition details: DELETE CICSLUKT.GWY.IAMTEST CLUSTER PURGE ERASE IF MAXCC = 08 - THEN SET MAXCC = 00 END DEFINE CLUSTER - (NAME(CICSLUKT.GWY.IAMTEST) - OWNER ($IAM) - RECSZ (1000 9500) PROGRAMMER ACTION: Take a system dump, contact your IBM Support Center and have the dump output, SYSLOG output, and a copy of the job stream available for problem determination. For shared resources, WRTBFR was issued, but: TRANSID was greater than 31,or The shared resource option (LSR) was not specified, or The LSR percentage value was not between 0 and 100. Check This Out Attempt has been made to store a record that would create a duplicate key in the indexed or relative file OR a duplicate alternate record key that does not allow duplicates.

X'F8' 248 Return Code=08 Action=OPEN IKQLAB or IKQSMVRJ (VSE/VSAM Space Management for SAM Feature) passed an invalid parameter list to the LABEL or EXTRACT marco. Idc3014i NOTE: VSAM provides an IDUMP of the region containing the VSAM control blocks, provided the SYSDMP is assigned. I know that IDCAMS is recommended for use with SMS-managed data sets, which is not what I was doing - still for some reason I decided IDCAMS was the way I'd

Specify the SYS EXTENT = command to increase the amount of space allocated for extent blocks.

The ACB for a SHAREOPTIONS (4) KSDS indicates MACRF = ADR, MACRF CNV but there are currently other ACBs open for keyed output access, or The ACB for a SHAREOPTIONS (4) Hmmm.... IN was specified (explicitly or by default), but an update request is made. Vsam Error Codes This information message indicates that the catalog records for this file are correct, but its catalog statistics may be incorrect.

If you cannot correct the error situation, contact your IBM Support Center. Return Code=08 Action=Request No record found. If this problem recurs often, it may be necessary for your system programmer to provide for a larger lock file using the DLF IPL command. this contact form Return Code=0C Action=Request VSAM failed to read index-set records of an index.

If the rerun fails, contact your IBM Support Center. Ensure that the correct volume was mounted; check your job control statements defining the catalog of CRA for possible errors. Rerun the job. PROGRAMMER ACTION: Probable job control error.